Make your own free website on Tripod.com
 
   
Title-Wind as alternative energy source
   
  Wind Turbine Towers
   
 

Wind turbine towers, Navarra, Spain Photograph Soren Krohn
© 1999 DWIA

 
 
 
 
 
 
 
 
 
 
     
    The tower of the wind turbine carries the nacelle and the rotor. Towers for large wind turbines may be either tubular steel towers, lattice towers, or concrete towers. Guyed tubular towers are only used for small wind turbines (battery chargers etc.)
   
   
    Tubular Steel Towers
   

NEG-Micon Tubular towers

Most large wind turbines are delivered with tubular steel towers, which are manufactured in sections of 20-30 metres with flanges at either end, and bolted together on the site. The towers are conical (i.e. with their diameter increasing towards the base) in order to increase their strength and to save materials at the same time. Photograph © NEG-Micon A/S 1998

   
   
   
   
   
   
   
     
    Lattice Towers
     
   

Nordex Lattice Tower

Lattice towers are manufactured using welded steel profiles. The basic advantage of lattice towers is cost, since a lattice tower requires only half as much material as a freely standing tubular tower with a similar stiffness. The basic disadvantage of lattice towers is their visual appearance , (although that issue is clearly debatable). Be that as it may, for aesthetic reasons lattice towers have almost disappeared from use for large, modern wind turbines. Photograph © Nordex A/S 1998

   
   
   
   
   
   
     
    Guyed Pole Towers
     
   

Genvind 22 guyed pole tower

Many small wind turbines are built with narrow pole towers supported by guy wires. The advantage is weight savings, and thus cost. The disadvantages are difficult access around the towers which make them less suitable in farm areas. Finally, this type of tower is more prone to vandalism, thus compromising overall safety. Photograph Soren Krohn © 1999 DWIA

   
   
   
   
   
 
 
 
 
 
     
    Hybrid Tower Solutions
     
   

Bonus 95 kW Hybrid Tower

Some towers are made in different combinations of the techniques mentioned above. One example is the three-legged Bonus 95 kW tower which you see in the photograph, which may be said to be a hybrid between a lattice tower and a guyed tower. Photograph © Bonus Energy A/S 1998

   
   
   
   
   
   
   
     
    Cost Considerations
     
    The price of a tower for a wind turbine is generally around 20 per cent of the total price of the turbine. For a tower around 50 metres' height, the additional cost of another 10 metres of tower is about 15,000 USD. It is therefore quite important for the final cost of energy to build towers as optimally as possible. Lattice towers are the cheapest to manufacture, since they typically require about half the amount of steel used for a tubular steel tower.
   
   
   
   
     
    Aerodynamic Considerations
     
    Generally, it is an advantage to have a tall tower in areas with high terrain roughness, since the wind speeds increases farther away from the ground. Lattice towers and guyed pole towers have the advantage of giving less wind shade than a massive tower.
   
   
     
    Structural Dynamic Considerations
     
    The rotor blades on turbines with relatively short towers will be subject to very different wind speeds (and thus different bending) when a rotor blade is in its top and in its bottom position, which will increase the fatigue loads on the turbine.
   
   
     
    Choosing Between Low and Tall Towers
     
    Obviously, you get more energy from a larger wind turbine than a small one, but if you take a look at the three wind turbines below, which are 225 kW, 600 kW, and 1,500 kW respectively, and with rotor diameters of 27, 43, and 60 metres, you will notice that the tower heights are different as well.
   
   
     
    Obviously, you get more energy from a larger wind turbine than a small one, but if you take a look at the three wind turbines below, which are 225 kW, 600 kW, and 1,500 kW respectively, and with rotor diameters of 27, 43, and 60 metres, you will notice that the tower heights are different as well.

225 kW Turbine600 kW turbine1,500 kW turbineHeight labels

Clearly, we cannot sensibly fit a 60 metre rotor to a tower of less than 30 metres. But if we consider the cost of a large rotor and a large generator and gearbox, it would surely be a waste to put it on a small tower, because we get much higher wind speeds and thus more energy with a tall tower. Each metre of tower height costs money, of course, so the optimum height of the tower is a function of

  • tower costs per metre (10 metre extra tower will presently cost you about 15,000 USD)
  • how much the wind locally varies with the height above ground level, i.e. the average local terrain roughness (large roughness makes it more useful with a taller tower),
  • the price the turbine owner gets for an additional kilowatt hour of electricity.
   
   
   
   
   
   
   
   
   
   
   
   
   
   
 
 
 
 
    Manufacturers often deliver machines where the tower height is equal to the rotor diameter. aesthetically, many people find that turbines are more pleasant to look at, if the tower height is roughly equal to the rotor diameter.
   
   
    BACK TO COMPONENTS
    Source:
    http://www.windpower.org/en/tour/wtrb/tower.htm